• 大区经理:张经理:18663767795
  • 大区经理:陶经理:13011716033
  • 技术咨询:詹经理:18663767799
  • 传真:0531-68850070
  • 地址:山东省济南市历城区工业北路58号恒大城K栋3-3109室
新闻资讯当前位置:PK10计划-新闻资讯
    全自动超声波清洗机不锈钢冲压件的清洗要求及验收标准
    2019-7-29 15:49:24
    全自动不锈钢冲压件超声波清洗机
    Automatic ultrasonic cleaning machine for stainless steel stamping parts
    一、不锈钢冲压件的清洗要求及验收标准:
    Cleaning requirements and acceptance standards for stainless steel stamping parts:
    清洗要求:彻底清洗工件表面灰尘、油污、干燥后清洗。
    Cleaning requirements: thoroughly clean the surface dust, oil, dry cleaning.
    验收标准:
    Acceptance criteria:
    1. 彻底清除工件外壁上的污垢;
    1. Clean the dirt on the outer wall of the workpiece thoroughly.
    2、不要划伤工件表面;
    2. Do not scratch the surface of the workpiece.
    3.确保清洗后的工件是干燥的。
    3. Make sure that the cleaned workpiece is dry.
    第二,清洁输出
    Second, clean output
    1. 篮子/ 2-4min;
    1. Basket/2-4 min;
    2、每篮清洗量视工件大小而定;
    2. The amount of cleaning per basket depends on the size of the workpiece.
    3.清洗总量为5000-7000件/小时。
    3. The total amount of cleaning is 5000-7000 pieces per hour.
    工件应提前用超声波粗加工清洗,以清除工件表面的大部分油脂、污垢、灰尘等附着物。然后用超声波细洗彻底去除污染物;工件表面的清洗剂通过一次冲洗去除;然后通过超声波二次冲洗完成清洗,最后通过两次内部循环烘干。
    The workpiece should be cleaned by ultrasonic roughing in advance to remove most of the grease, dirt, dust and other attachments on the workpiece surface. Then the contaminants are thoroughly removed by ultrasonic fine washing; the cleaning agent on the surface of the workpiece is removed by one rinse; then the cleaning is completed by ultrasonic second rinse, and finally dried by two internal cycles.
    全自动封闭式超声波清洗机的“清洗工艺”
    "Cleaning Technology" of Fully Automatic Closed Ultrasound Cleaner

    喂养→不。1超声波清洗→NO。2超声波清洗→NO。3喷淋冲洗→无。4超声波清洗→无。5超声波清洗→无。6 。纯水慢抽→不抽。7热风内循环干燥→无。热风内循环干燥→下料。

    全自动超声波清洗机

    Feeding No. 1. Ultrasound cleaning NO. 2. Ultrasound cleaning NO. 3. Spray rinse none. 4. Ultrasound cleaning none. 5. Ultrasound cleaning none. 6. Slow pumping of pure water no pumping. Hot air internal circulation drying none. Hot air internal circulation drying blanking.
    自动超声波清洗机“结构组成及功能介绍”
    Introduction to the Structure and Function of Automatic Ultrasound Cleaning Machine
    超声波通道结构(四边呈锯齿状):
    Ultrasound channel structure (serrated on all sides):
    1、主清洗水箱上方,加工成锯齿状,让油从四个方向溢出;这样可以快速、均匀地排出油脂和杂质,有利于产品的清洗。
    1. Over the main cleaning water tank, the oil is processed into zigzag shape, so that oil spills in four directions. This can expel oil and impurities quickly and evenly, which is conducive to product cleaning.
    2、随城市水进入水、溢流口、排水口、过滤器循环进水口、溢流口为暗溢流网。
    2. Dark overflow network is formed when urban water enters water, overflow, drainage outlet, filter circulating inlet and overflow outlet.
    储层结构:
    Reservoir structure:
    1. 设置溢流口,满液后自动溢流进入主排水管道;
    1. Set up an overflow outlet and automatically overflow into the main drainage pipeline after filling the liquid.
    2. 清洗罐溢流进入储液罐底部(创新的防泡沫设计)。如果在除油部位设置油分离,可以有效地将油从水中分离出来。循环泵过滤后返回循环中的清洗槽;
    2. cleaning tank overflow into the bottom of the storage tank (innovative anti foam design). Oil can be effectively separated from water if oil separation is set in the deoiling part. The circulating pump filters and returns to the cleaning tank in the circulation.
    3.储液罐外壁粘贴10mm保温棉保温;
    3. Insulation with 10mm insulating cotton on the outer wall of liquid storage tank;
    4、不锈钢水箱盖,带手柄。
    4. Stainless steel tank cover with handle.
    机械手系统“原理”:
    Manipulator System "Principle":
    采用多臂机械手,可同时提起十个洗涤筐,水平移动一个工位。清洗左进右出,PLC控制整机运行,机械定位采用非接触感应开关和旋转编码器,限位采用行程开关,机械手行程误差可自动停止,防止机械手碰撞。
    With a multi-arm manipulator, ten washing baskets can be raised at the same time and one station can be moved horizontally. Cleaning left in and right out, PLC control the operation of the whole machine, mechanical positioning using non-contact induction switch and rotary encoder, limit using stroke switch, manipulator travel error can automatically stop, to prevent collision of the manipulator.
    电子控制系统:
    Electronic control system:
    该部件属于整机自动机械化控制的核心。具有各槽位的跟踪、监控和程序控制功能。
    This part belongs to the core of automatic mechanical control of the whole machine. It has the functions of tracking, monitoring and program control of each slot.
    电控柜采用A3钢板折弯焊接而成,磷化处理后,表面防腐处理,颜色为蓝色,面板为乳白色(可根据用户定制)。
    The electric control cabinet is made of A3 steel plate by bending and welding. After phosphating treatment, the surface is anticorrosive, the color is blue, and the panel is milky white (customizable according to users).
    以上是全自动超声波清洗机厂家为大家整理的相关内容,想要了解更多内容,欢迎网站:http://www.spn-biz.com
    Above is the relevant content of the automatic ultrasonic cleaner manufacturer for you. For more information, welcome to the website: http://www.spn-biz.com.
全天PK10计划 PK10计划 PK10计划 测试站点 PK10计划 PK10计划 PK10计划 PK10计划 PK10计划 pk10